SpudFiles

After seeing the S400, I thought I have to make a Sniper and so I have been looking around at copper rifles, and it seems like they can hold pretty high pressures. How much pressure can a copper pipe hold alone? and is a sweated joint weaker than the pipe itself? I was thinking of using a shock pump with it.

I myself have been inspired by Chaos' S400 and the SSS. I also plan to use copper but I'm going to be using compression fittings aswell as brass fittings on the valve.

This is the overall look of the gun I hope to achieve. As much as I love Chaos's gun, I hate copying at all so I've given his design my own touch for what I think will suit me best.

Anyway back to your question, a shock pump will absolutely kill your arms if your planning something at the same scale as his. He has a mightly large air chamber so you might have to use what you have (eg a bike pump, compressor) or upgrade to making a high pressure pump or buying a commercial high pressure 260psi floor pump. I'm not overly sure about soldering, hence why I've gone with comp fittings. If you have the tools, soldering is a top way to go so best of luck with your build.

Hope this is some help to you.

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.

Thats quite a lot of pressure. Is that the same with comp fittings though?

I have had one compression fitting fail on me, as in, rip the Olive of from around the pipe. This was because the fitting wasn't tightened fully, and because i was using 400PSI.

Soldered/sweated fittings are much more robust in my experience.

Have you considered using epoxy

Sweated/soldered/capillary fittings will take the same pressure as the pipe when connected properly.

Using 95/5 tin antimony solder and pressure fittings, copper joints between 1/8" and 1" are rated for 1090 psi. 1" Type M copper tube is rated for 580 psi, and bursts at somewhere well over 3kpsi. I don't know if they will survive the same pressure as the pipe, but, assuming Type M pipe, the joints are rated for more than the pipe itself.

Thanks guys. This will really help. It seems as if a shockmate, which claims to go to 400 psi should work fine with copper. So shock pumps require lots of effort for a chamber that size? So maybe a high pressure pistol would be a better plan? Or a lower pressure sniper...

A high pressure sniper works very well. use a small chamber (3 cubic inces or less) and about 400 PSI.

It takes me about a minuite to get to 400PSI on my BB sniper. It has about 2" of 15mm pipe for the chamber. For larger volumes, expect alot more pumping.

Hmm, so if I wanted to make a paintball Co2 reg, could I use copper with only screw-in fittings? I can not weld anything, so what metal do you recommend?

chartreusesnot wrote:So maybe a high pressure pistol would be a better plan? Or a lower pressure sniper...

Or a homemade pump, which is the perfect solution to all high pressure/mid volume situations.

I made this test piece in a metalwork class. It is a few pipes welded/brazed together in various ways. The main body is just normal steel pipe, with a seam. The end bits on the wide pipe are just steel plate which has been butt welded, with a mixture of brass brazing and the others just melted steel/filler rod. One has a brass nut brazed onto the outside with Silfos, which is a faily low temp brazing product for brass and copper ( cant remember exactly which is used cus made it a while back) Up the top there is a copper pipe with a piece of flat copper butt brazed to the end of it, not a cap, just a flat piece of copper. It was dones with silfos, or silver solder, one of them lol.

Anyway, the thing was filled with water and a pump attaced to the brass nut. It was then pumped up to 1800psi, which is pretty high, the flat plates that were butt welded on all bowed out because of the pressure, but the thing held. Only had one tiny pinhole leak. Im not sure it it would be the same as with air, but I dont see why not. If done correctly, brazing/soldering creates a very strong joint. This was all done with a oxy acet torch.

why won't it let me delete this message??
all I get are the quote and edit options...

Ragnarok wrote:

chartreusesnot wrote:So maybe a high pressure pistol would be a better plan? Or a lower pressure sniper...

Or a homemade pump, which is the perfect solution to all high pressure/mid volume situations.

and how might I do this safely?