will this work?? piston valve
-
The_Kangsta
- Private 4
- Posts: 69
- Joined: Sat Oct 27, 2007 9:20 pm
- Location: Canada
Will this idea work? its not really a *proper* barrel sealing valve, but it should work.
- Attachments
-
- piston valve.jpg (9.41 KiB) Viewed 2168 times
Live now, die later
-
Gippeto
- First Sergeant 3
- Posts: 2503
- Joined: Sat Jan 19, 2008 10:14 am
- Location: Soon to be socialist shit hole.
- Has thanked: 2 times
- Been thanked: 17 times
If it was a straight pipe, it would be a co-ax. Which is just fine! 
Comments;
If that is anywhere near scale, you should reduce the pilot volume.
Otherwise, jrrdw gives good advice, as always.
Comments;
If that is anywhere near scale, you should reduce the pilot volume.
Otherwise, jrrdw gives good advice, as always.
"It could be that the purpose of your life is to serve as a warning to others" – unknown
Liberalism is a mental disorder, reality is it's cure.
Liberalism is a mental disorder, reality is it's cure.
-
potatoflinger
- Sergeant 2
- Posts: 1136
- Joined: Thu Nov 02, 2006 3:26 pm
- Location: Maryland
It will work, it is pretty much just a coaxial piston valve with a tee and another air chamber coming out of it.
It's hard to soar with eagles when you're working with turkeys.
-
mobile chernobyl
- Corporal 3
- Posts: 756
- Joined: Sun Dec 03, 2006 11:53 am
- Been thanked: 7 times
What size Tee is that you plan on using? If its a 2" I have a way better design thats just as easy to make that I use on my "1 gallon" launcher.
-
Mr.Sandman
- Corporal 3
- Posts: 762
- Joined: Fri Mar 28, 2008 9:10 am
- Contact:
pretty good but why this design? also what do you plan on using as your piston? wait nevermind i was looking at it wrong.
while your talking about pilot volume, what would be a good pilot volume for a 1.5" chamber co-axGippeto wrote:If it was a straight pipe, it would be a co-ax. Which is just fine!
Comments;
If that is anywhere near scale, you should reduce the pilot volume.
Otherwise, jrrdw gives good advice, as always.
-
MrCrowley
- Moderator
- Posts: 10078
- Joined: Fri Jun 23, 2006 10:42 pm
- Location: Auckland, New Zealand
- Been thanked: 3 times
The arrows show that the chamber is not to scale and will be longer i'm guessing.Coodude26 wrote:Whats with the arrows at the end of the chamber?
And no one can tell you for sure if something will work or not because you haven't even built it yet.
He is wondering if the concept will work, if you understand physics you can tell if something will work before building it...idiot.
-
Gippeto
- First Sergeant 3
- Posts: 2503
- Joined: Sat Jan 19, 2008 10:14 am
- Location: Soon to be socialist shit hole.
- Has thanked: 2 times
- Been thanked: 17 times
You didn't say what your barrel id was so I'll just give an example.
If your barrel id is other than .750" you can adjust things accordingly.
Just remember that TOTAL PISTON TRAVEL should (ideally) be equal to id/4 minimum. A little bit more is okay, a little bit less will hurt performance.
Theoretical canon as follows:
Barrel inside diameter of .750inches
Chamber inside diameter of 1.50inches
Ideal piston travel is barrel id divided by 4.
So your piston should move .750"/4 or 0.1875" (3/16") before hitting your bumper. (Mouse pad, camping mat, etc.)
This would make your theoretical "ideal pilot volume" roughly
pi*r*r * .1875" or 3.14*.750*.750*.1875 = 0.3312cu.in.
Hint: Use this number in ggdt to size your pilot valve. Increase/decrease the pilot diameter until you eliminate piston bounce.
Okay, that's in an ideal world. In "our world", call it 1/4" of total piston travel, and a pilot volume of 0.44 cu.in.
If your barrel id is other than .750" you can adjust things accordingly.
Just remember that TOTAL PISTON TRAVEL should (ideally) be equal to id/4 minimum. A little bit more is okay, a little bit less will hurt performance.
Theoretical canon as follows:
Barrel inside diameter of .750inches
Chamber inside diameter of 1.50inches
Ideal piston travel is barrel id divided by 4.
So your piston should move .750"/4 or 0.1875" (3/16") before hitting your bumper. (Mouse pad, camping mat, etc.)
This would make your theoretical "ideal pilot volume" roughly
pi*r*r * .1875" or 3.14*.750*.750*.1875 = 0.3312cu.in.
Hint: Use this number in ggdt to size your pilot valve. Increase/decrease the pilot diameter until you eliminate piston bounce.
Okay, that's in an ideal world. In "our world", call it 1/4" of total piston travel, and a pilot volume of 0.44 cu.in.
"It could be that the purpose of your life is to serve as a warning to others" – unknown
Liberalism is a mental disorder, reality is it's cure.
Liberalism is a mental disorder, reality is it's cure.
MrCrowley wrote:The arrows show that the chamber is not to scale and will be longer i'm guessing.Coodude26 wrote:Whats with the arrows at the end of the chamber?
And no one can tell you for sure if something will work or not because you haven't even built it yet.
He is wondering if the concept will work, if you understand physics you can tell if something will work before building it...idiot.
No need to insult me. I just didn't want him to get over-excited when a couple people tell him it would work, and then be careless with the construction.