Short question topic

[Gippeto]

Haven't used nylon in a poppet style valve...have used Nylatron for a few though. Works fine at 3000psi.

I use an undercut design on the valve stem and face off the valve body flat. The stem is undercut with a ball end router bit, and the sharp edge faced off to leave a flat ~ .020" wide. The plastic part of the stem is ~ .060" wider than the port.

Seals easy (have never had to lap one), really good flow, and no wedging effect from the pressure.

[Gun Freak]

I got another vacuum motor but this time it's way smaller and runs off a rechargeable battery (chordless vacuum). So it's also much weaker... Maybe it won't nearly kill me like the last one So anyway, my question is since this is DC, is it possible to run it on AC without blowing it up?

[Gun Freak]

Anyone...

[warhead052]

You could try, if you got it free then its worth a shot.

[MrCrowley]

I got another vacuum motor but this time it's way smaller and runs off a rechargeable battery (chordless vacuum). So it's also much weaker... Maybe it won't nearly kill me like the last one So anyway, my question is since this is DC, is it possible to run it on AC without blowing it up?

Just find some form of charger that converts AC to DC. You could probably grab the charger for the vacuum battery and just wire it directly to the vacuum motor assuming the vacuum motor draws what the charger puts out. I've used 12v drill chargers to rewire and power fridge compressors.

I'm by no means an expert but my understanding is that you can use a 240v (or whatever you use in America) to 12v (or whatever the vacuum motor runs off) transformer that has a rectifier in it. The transformer steps down the AC voltage and then I assume there is a rectifier that turns it in to DC from AC.

[warhead052]

Crowley, if we used 240v our stuff would fry out in a heat beat. I am pretty sure its 120v for most things, but 240v for stuff like washing machines and ovens and that sort.

[MrCrowley]

Yeah well just use whatever it is you use in America, 240v was just an example

[warhead052]

Haha, yeah. I suppose a decent ac to dc converter would work Gun Freak, unless you are trying to change the way the motor spins.

[Gun Freak]

Alright so if I find a battery charger with ample voltage (I'm aiming for 12) and snip the connector off and split the wires, I can connect that to my motor? I'm a total electronics noob. I found a 12V and a 9V charger but I don't wanna cut any of em up. I'm gonna keep looking around though, I'm sure I'll find a 12V charger that I don't use.

[warhead052]

Might work, what was the original voltage for the motor?

[Gun Freak]

I don't know because the battery wasn't in the vacuum when I got it (from a trash pile) and I was stupid not to peruse the vacuum for specs. But I didn't see anything on it while ripping it apart. I am gonna try to look up the model and find out the voltage. I'm guessing it was 12, because my tests with a 9V didn't seem strong enough for a vacuum.

[MrCrowley]

Check how much current it draws as well; this will have to be equal to or less than the output current of the power supply charger.

[Gun Freak]

I know it draws a lot, because it drained a 9V in about a minute of running. I don't know if current draw will be something I can figure out but I'll try.

[MrCrowley]

A voltmeter should do it though I am surprised there's nothing on the vacuum motor itself.

[warhead052]

A charger won't cut it. Trust me... My shitty emergency 12v compressor won't even run on a 12v charger, I even tried a 24v to see if it would boost it but nope. So try finding just a solid step down transformer, from 120 to 12v to make sure you have a steady flow of current, rather than the ridiculous drip flow of a charger.