A mini pneumatic?

[noname]

A barrel bigger than 3/16" ID is too big, just to give you an example of a tiny barrel.

[Dom]

For a blowgun?..

Then I'll stick on to the ball valve

[minispuder]

just mod a super soaker. put a bicycle tube valve for a new pump.

it has a quick release ball valve using a spring.

[Dom]

just mod a super soaker. put a bicycle tube valve for a new pump.

it has a quick release ball valve using a spring.

Not a bad idea...

[SpudBlaster15]

Lorem ipsum dolor sit amet, consectetur adipiscing elit. Cras nec placerat erat. Vivamus dapibus egestas nunc, at eleifend neque. Suspendisse potenti. Sed dictum lacus eu nisl pretium vehicula. Ut faucibus hendrerit nisi. Integer ultricies orci eu ultrices malesuada. Fusce id mauris risus. Suspendisse finibus ligula et nisl rutrum efficitur. Vestibulum posuere erat pellentesque ornare venenatis. Integer commodo fermentum tortor in pharetra. Proin scelerisque consectetur posuere. Vestibulum molestie augue ac nibh feugiat scelerisque. Sed aliquet a nunc in mattis.

[minispuder]

i did it myself. it works pretty good with air soft bbs.

[ballad of NJ]

Use a nerf valve thats what I used for my ghetto gun.

[jjk92]

For a blowgun?..

Then I'll stick on to the ball valve

good choice a ball valve would work much better i used a blowgun on a mini that shot airsoft and chunks of potatoe and it did not have the effect i desired (more than 100 ft but if that works for you then get a blowgun) but it did hurt like crazy if you pumped it up to 160psi and got shot with it.....thats in theory of course because everyone knows never to shoot at people

[iknowmy3tables]

100ft, mini, thats pretty good, I bet you could make a coaxle, and using a rubber schrader as an refill, actuator, even a bumper for pistons

[kf4oij]

Holy Crud this forum gets no traffic, what the heck is a "Blow Gun Valve"??

And isn't a ball valve a little too slow for a mini? Has anyone got any experience doing this?

[integral]

blowgun:

[spudthug]

he need an inline one for this and that was pretty off topic...dont bring back month old posts jsut to do that....the only reason im doing it is because i was gonna ask where to get brakeling and tell them i am going to make one out of a blowgun valve today.....

[SPG]

Build a tiny coaxial with a schraeder as both fill and trigger valve perhaps?

In fact here's a thought. Buy a cheap plastic double action cap gun, you can find them all over e-bay and similar.

Hack the poor thing apart so that you keep the grip, trigger group, hammer and some of the barrel but remove the receiver. Replace this with a schraeder valved co-axial, so that the hammer when it falls forward hits the valve core.

Bodge the whole lot together with glue, duct tape, bondo, and spit.

Voila cool(ish) looking mini co-axial pneumatic. If you built this with a decent chamber which could actually take a reasonable pressure you could probably get all this in one of those break opening revolvers, and put the chamber where the cylinder would usually be.

*off to toy shop now*

[jackssmirkingrevenge]

hey SPG, I see you're missing spudtech too

I think you had proposed the idea above when you had seen my mini-coaxial too.

[spudthug]

my two mini pnematics...dont use a blowgun as the valve terrible flow...

http://www.spudfiles.com/forums/viewtopic.php?t=6970&

http://www.spudfiles.com/forums/viewtopic.php?t=6733&